Coronavirus: Information & Resources

ACTIVE INGREDIENT

PRODUCTS

USE DIRECTIONS

1. Spray the surface until thoroughly wet
2. Leave for 30 seconds to sanitize or 10 minutes to disinfect.
3. Wipe away when desired contact time has passed.

1. Thoroughly wet nonporous surface and rinse.
2. Spray product on and let stand for 10 minutes.
3. Rinse or wipe away product after 10 minutes.

1. Hold container upright 6 - 8" from nonporous surface.
2. Cover the surface thoroughly until wet.
3. Let stand for 5 minutes.
4. Wipe off.

1. Hold container upright 6 - 8" from surface (WORKS ON BOTH PORUS AND NONPORUS).
2. Cover the surface thoroughly until wet.
3. Let stand for 30 seconds to 1 minute.
4. For best results, let air dry to increase contact time.

1. Hold upright, press button and spray towards the center of a room for 10 seconds. OR.
2. Pre-clean surface and then hold upright 6-8" from surface. Spray for 2-3 seconds until covered with mist.
3. Let stand for 10 minutes and allow to air dry.

1. Flush toilet.
2. Apply 6 oz. under and around rim.
3. Scrub entire bowl.
4. Let sit for 5 minutes.
5. Flush toilet.

1. Spray until thoroughly wet.
2. Let stand for 10 minutes then wipe clean.

1. Flush toilet to remove any excess dirt
2. Directly pour 3/4 cup (6 oz.) of product inside bowl to completely coat the sides of the bowl and under the rim
3. Clean up spills and drips immediately
4. Do not close the toilet bowl lid.
5. Let stand for at least 5 minutes.
6. Brush entire bowl to wet surfaces thoroughly, including under the rim, and flush.
7. Rinse brush in fresh water after use.
8. Repeat if necessary.

1. Pre-clean visibly soiled areas.
2. Pull cloth from dispenser and wipe hard, non-porous environmental surfaces.
3. Allow the Oxy-1 Wipes solution to remain visibly wet for 1 minute. Use additional cloths if needed to ensure the correct wet-contact time.    
4. Allow surface to air dry.

1. Spray directly onto pet stain until complete covered.
2. Rinse with water or wipe with a clean, damp cloth.

1. Pour the hydrogen peroxide into the spray bottle.
2. Spray down the hard surfaces in your bathroom, kitchen, living room and bedrooms you are trying to disinfect (tubs/showers, trashcans, doorknobs, toilets, sinks, etc.).
3. Allow the solution to bubble on the surface for at least 5 minutes.
4. Wipe off.

1. Pre-clean the area so it's free of dirt.
2. Spray the surface until it is totally wet.
3. Let the spray sit on the surface for ten minutes.
4. Use a dry paper towel or lint-free clean cloth to wipe the surface.
5. If the surface regularly comes into contact with food, you must rinse it with water after sanitizing to prevent food picking up the cleaner.

1. Pre-clean heavily soiled areas
2. Spray the surface until it is totally wet.
3. Let the spray sit on the surface for 10 minutes.
4. Use a paper towel or cloth to wipe surface.
5. Let surface air dry.

1. Spray on the surface.
2. Let product sit on the surface for at least 10 minutes.
3. Allow the surface to air dry if possible, or wipe off after 10 minutes.

1. Spray on the surface.
2. Let sit on the surface for at least 10 minutes.
3. Allow the surface to air dry if possible, or wipe off after 10 minutes.

1. Wipe hard non porous food-contact surfaces with a wipe until the surface is visibly wet.
2. Allow the surface to remain wet for 10 minutes. Let air dry.
3. If surfaces are extremely dirty, clean first with another wipe before disinfecting.
4. Discard used wipe in the trash. Do not flush in toilet.
5. Rinse food-contact surfaces with clean, potable water after disinfecting. Do not use to disinfect dishes, glassware or utensils.

1. Turn nozzle to ON.
2. Tilt bottle at a downward angle while spraying.
3. Wait a few minutes.
4. Wipe with sponge or cloth.

1. Hold can upright 6 - 8 inches from surface.
2. Spray surface until thoroughly wet.
3. Let stand for 5 minutes.
4. Allow to air dry.
5. Rinse with potable water for food-contact surfaces.

1. Raise toilet seat, flush bowl and remove heavy soil by scrubbing with a stiff brush prior to using product.
2. Point top of bottle down into bowl and squeeze gently, dispensing at least 4 oz. of the thick formula under the rim and on the sides of the bowl, letting it run down into the water.
3. Do not close toilet bowl lid.
4. To disinfect, let stand for at least 15 minutes.

1. Use full-strength or dilute ¼ cup (2 oz.) per gallon of warm water.
2. Apply to surface until thoroughly wet.
3. Wipe with a clean cloth, sponge, or mop.
4. To sanitize pre-clean the surface by leaving the produce on for 1 minute before wiping.
5. To disinfect, pre-clean the surface by leaving the product on for 10 minutes before wiping.
6. Rinse all food contact surfaces with water after using the product.

1. Spray 6–8 inches from surface until thoroughly wet.
2. Let stand one minute.
3. Wipe with a clean cloth or paper towel or allow to air dry.
4. Rinse surfaces that may come in contact with food with potable water. For all other surfaces, no rinsing is required.

1. Pre-wash surface.
2. Mop or wipe with bleach solution. Refer to your product label for dosing instructions.
3. Allow solution to contact surface for at least 6 minutes.
4. Rinse well and air dry.

1. Wipe area with a solution of ½ cup of Clorox® Regular Bleach2 with CLOROMAX® per gallon of water.
2. Allow solution to contact surface for at least 5 minutes.
3. Rinse well and air dry.
4. To sanitize, wash rinse and wipe surface are with a solution of 2 teaspoons of bleach per gallon of water for at least 2 minutes.
5. Let air dry.

1. Flush toilet.
2. Apply 6 oz. under and around rim.
3. Scrub entire bowl.
4. Let sit for 5 minutes.
5. Flush toilet.

1. Remove excess dirt.
2. Spray product 4–6” from surface until thoroughly wet.
3. Let stand for 30 seconds.
4. Rinse or wipe clean.

1. Flush toilet before cleaning.
2. Apply 6 oz. to coat the bowl including under the rim. Do not dose lid.
3. To clean: scrub entire bowl and under rim thoroughly. Disinfect: let sit for 5 minutes. Sanitize: let sit for 30 seconds. Then flush.
4. Rinse brush in fresh water after use. Repeat if needed.